If you see the picture... great. Seems as if I've had trouble posting pics. If not, looks like I still am.
Here's the situation. Guy has purchased a soft side semi trailer. There is a logo and lettering on both sides. He wants them removed or covered and then I put his logo in that spot.
The material is a heavy vinyl-tarp-fiberous-plasticky stuff. The current logo appears to be screened or stencil masked... the ink (or paint )is pretty heavy.
I just looked at this about 15 minutes ago, so I have not attempted to use anything to remove the current logo, like Lacquer Thinner.
I'm wondering if anyone has worked with this stuff before... what did you do? And when putting the new logo on (this soft side moves like an accordian) what do you use that will hold up to this thin being folded and used daily? Paint? Vinyl? Screen Ink? Should I try to remove it or simply cover it up? With what?
Thanks!
-------------------- Jeff Vrstal Main Street Signs 157 E. Main Street Evansville, WI 53536 1-608-882-0322 Posts: 670 | From: Evansville, Wisconsin | Registered: Sep 2001
| IP: Logged |
posted
This isn't the solution but it is a warning. Don't go at it with screenink thinners as this will attack the material and begin to disolve it.
As far as I have been taught, The process of screening is that the ink will bite into the surface by disolving the top layer of the material a tiny bit and so removal would be impossilbe without damage.
Sorry I can't advise on best course to take.
-------------------- Miles Cullinane, Cork, Ireland.
From the sometimes sunny south of Ireland, Posts: 914 | From: Cork, Ireland | Registered: Jul 1999
| IP: Logged |
Looks like about a 4'x5' logo & lettering. Don't try to do it on the truck! Find a bench or table that you can lay it on, stock up on laquer thinner, or prefferably MEK, and a case of paper towels. Cover the area with paper towels soaked with the MEK and let it bite thru the ink for a while, then start wiping with MEK dampened paper towels. Repeat until it's cleaned off! Let it dry in the Sun while you do the other one.
*WARNING* Do this in a well ventilated area! Don't store the wet towels in a closed container as the might ignite by spontainious combustion, like oily rags!
NOTE...the red may leave a stain. So plan on having some sort of panel to hide it and replace the bit of surface that might be removed.
DON'T bid this job cheap! It's gonna be a lot of work.
[ March 22, 2002, 04:56 PM: Message edited by: Si Allen ]
-------------------- Si Allen #562 La Mirada, CA. USA
(714) 521-4810
si.allen on Skype
siallen@dslextreme.com
"SignPainters do It with Longer Strokes!"
Never mess with your profile while in a drunken stupor!!!
Brushasaurus on Chat Posts: 8831 | From: La Mirada, CA, USA | Registered: Nov 1998
| IP: Logged |
posted
Mark clued me in to this post - he thinks I might know something. What I know is that I would not even THINK of removing that logo. I would not work on this material unless it's off the truck. Then I would talk the customer into my painting out the existing copy with a large rectangle of black over the whole thing ( or a shape that will be pleasing with the future Logo ) and then put the new Logo and info onto the black.
I think that not only do you have a less than 5 percent chance of getting it off without either disfiguring or ruining the substrate, your health/time/skin/lungs are more important than this job. I have not yet mentioned peace of mind or losing your religion.
You can test for ink adhesion in areas of the hem, of course. Regular vinyl screening ink, thinned down, and rolled on in a couple of coats will probably do it. If not you might use ti-coat as a sealer and then you can use one shot if you like, or almost anything else.
With this type of job I have learned to tell the customer how I will do it and that's that. If that's not acceptable, then I can't guarantee the result, and walk away. We don't have to meet every challenge.
By the way, shouldn't that E sit on an about 17 degree angle:)
-------------------- Myra A. Grozinger Signs Limited Winston-Salem, NC
signslimited@triad.rr.com Posts: 1244 | From: Winston-Salem, NC USA | Registered: Nov 1998
| IP: Logged |
posted
I've done a few of these. I stencil masked and used vinyl screen ink ... so far holding up great after a couple years. If that's what's on there it isn't going to come off without making a major mess and leaving a ghost image... or melting/ruining the material. "Maybe" you could do a banner/panel and have it sewn over the existing logo.
-------------------- Compulsive, Neurotic, Anti-social and Paranoid ... but basically Happy Posts: 2677 | From: Rochester, NY, USA | Registered: Nov 1998
| IP: Logged |
posted
Vinyl inks are great for this type of application if you're the first one on it. Being a repaint has some problems though. Not with painting a panel over it, but when you try to brush on the new copy over the fresh panel. You'll be pulling up the panel color into your brush strokes. You'll either have to use a stencil for the copy and spray/roll it on, letter it first then cut in around all the new copy with a panel, or (what I'd probably do), bag the vinyl ink altogether and go with tie coat and enamels. Hope that made sense.
SONGPAINTER Original Sign Music by Sign People NOW AVAILABLE on CD and the proceeds go to Letterville's favorite charity! Click Here for Sound Clips! Posts: 1974 | From: Orleans, MA, Cape Cod, USA | Registered: Nov 1998
| IP: Logged |
posted
I wouldn't even attempt to clean this off. I'd scrub down the area, mask off what's there, and paint on some vinyl screen ink, thinned down, and with some aluminum powder added, as a "primer/blocker" coat. When that dried, I'd second coat it with straight white. Under no circumstances would I apply MEK, lacquer thinners, or any other "hot" type thinner to the vinyl fabric. This might dry out the plasticizers, causing the fabric to fail prematurely, and I wouldn't wish to be replacing one of those tarps. The revised lettering could then be applied over the covering patch, and I'd opt for using cut vinyl letters. To hand letter over that base would require triple-coating to get decent coverage, as the base layer would always bleed through a bit.
-------------------- Ken Henry Henry & Henry Signs London, Ontario Canada (519) 439-1881 e-mail: kjmlhenry@rogers.com
Why do I get all those on-line offers to sell me Viagara, when the only thing hardening is my arteries ? Posts: 2689 | From: London,Ontario, Canada | Registered: Feb 1999
| IP: Logged |
posted
Joe Rees is correct in suggesting ticote and enamels. That is most likely what is on there now given the thickness of it. I have done a few of these myself. This material is begging for vinyl inks if like Joe said you are the first one there.
One thing I had run into is this material or materials that I worked on were extremely hard to get clean after being on the road for a given amount of time. I had used Ticote and enamels, but eventually failed because of poor adhesion. Not because of Ticote. but because of dirt.
I had done several test peices with positive results on new fabric with ticote and chromatic.
I no longer do these, I never seemed to get enough money to justify the agrivation.
Not to mention the company was a chore to deal with.
-------------------- Bob Rochon Creative Signworks Millbury, MA 508-865-7330
"Life is Like an Echo, what you put out, comes back to you." Posts: 5149 | From: Millbury, Mass. U.S. | Registered: Nov 1998
| IP: Logged |
posted
Don't even try to disolve that off!.what a mess!! I haver never looked at one of those up close and dont know how they are constructed, but an awning shop would be able to either sew in or heat seal in new panels I should think.An added benefit to that would be that you could work on JUST those panels, before they were put in.Getting to know an awning shop might bring you some work from them too. Use Naz-Dar VF series or some similar ink,.... mask with tape and use a roller.
-------------------- James Caley JCI Int'l 655 State College #19 Fullerton, CA USA 92831 jamez31@msn.com 714-773-9048 Posts: 16 | From: 655 state College #19, Fullerton CA USA 92831 | Registered: Feb 2002
| IP: Logged |
posted
Call the company that built the truck. One of my clients bought one of these trailers..the mfg. offered to install the logo on the curtains. If the mfg. doesnt do in house installation and printing..maybe they can give you a lead to someone who can help. Id bet a sewn patch would be good..I agree with Bob...its gonna be a bear to get used curtains clean. A canvas company or boat canvas shop will do a nice job
posted
I ran into a couple of those jobs before and the cheapest way out was to apply your graphic to a fresh piece of heavy outdoor grade reinforced vinyl (Like on billboards) and apply it (with contact cement or similar)over that graphic (like wallpaper)after the existing surface has been cleaned well and prepped. The existing logo has been burned well into the material...
-------------------- AirbrushBobby.com Clearwater, FL The message of the cross is foolishness to those who are perishing.1Cor1:18 “The wages of sin is death, but the free gift of God is eternal life in Jesus Christ our Lord”Rom6:23 Posts: 505 | From: Clearwater Florida USA | Registered: Feb 1999
| IP: Logged |
posted
Is there anyway you could flip them over and use the back?or switch the 2 sides and paint the backs?Just a thought. Steve Spiry Maddartist signs
-------------------- "I can draw anything but unemployment" Steve Spiry Madd Artist Murals&Signs Brandon,Mb. Canada Posts: 66 | From: Brandon,Mb. Canada | Registered: Jul 2001
| IP: Logged |
posted
Thanks, everyone, for all the great info on this. It does look like this was mask applied using a screen ink as the lettering and logo are fairly thick... much thicker than vinyl or paint.
Turning the curtain around will not work as there is obviously an "inside" and an "outside".
I had a feeling that this was pretty well embedded into the material and know well how red will come back to haunt me.
I like the patch idea... and checking with the manufacturer. I also think that the covering up with a coat or two of ink and then lettering with vinyl might work. I wondered about how the vinyl (high performance) would hold up as the curtain was folded open and closed over and over. Perhaps I just tell the guy that we may need to re-do it sooner with no guarantees.
Anyway, thanks again... I'll update this later.
-------------------- Jeff Vrstal Main Street Signs 157 E. Main Street Evansville, WI 53536 1-608-882-0322 Posts: 670 | From: Evansville, Wisconsin | Registered: Sep 2001
| IP: Logged |
![[Eek!]](eek.gif)
![[Cool]](cool.gif)
![[Confused]](confused.gif)
Printer-friendly view of this topic