posted
Here's the problem...Installed a Belkin USB card in my G3 Mac, as well as the most current drivers. My system profiler/device manager showed the USB card present, and is showing the Optical mouse present as well. The light on the mouse is on, so it's getting power from the USB port, but it's showing that the mouse isn't present in the mouse setup control panel.
Tech support from Logitech (mouse company, not Disney related, but COULD be.) was futile....they have computers answering all the questions, which is kinda ironic being that computers are the problem.
[ November 19, 2002, 09:27 AM: Message edited by: Don Coplen ]
posted
Don,..did you press the little button on the bottom of the mouse holder and on the mouse to make sure the reciever is getting signals from the mouse?
-------------------- fly low...timi/NC is, Tim Barrow Barrow Art Signs Winston-Salem,NC Posts: 2224 | From: Winston-Salem,NC,USA | Registered: Nov 1998
| IP: Logged |
posted
oops!!! worth a try just the same,...I don't know about macs mind you but often on pc's I've had to remove the old mouse drivers and or the mouse to get a new one to work,...
-------------------- fly low...timi/NC is, Tim Barrow Barrow Art Signs Winston-Salem,NC Posts: 2224 | From: Winston-Salem,NC,USA | Registered: Nov 1998
| IP: Logged |
posted
Timi...that makes sense, but it's a bit scary. If I remove the old mouse drivers, and the new mouse still isn't detected....how do I get things back again? Won't I be without a way to move the cursor if it fails to work????
Can you tell us the order of the steps you took after installing the pci-usb card? I.e. 'step 1: installed pci card, step 2: installed drivers, step 3: plugged in usb mouse, step 4: etc...'
Sometimes you just have to un-install drivers and then reboot-and plug in the usb cable and THEN install. In other words, usb can be funny with the order that you do things in.
Anyway, if you can tell us what order you did things in, that may help for troubleshooting.
-shane
-------------------- Halo Graphics Clearlake Oaks, CA http://www.halographics.com ntshane1@halographics.com Posts: 308 | From: Clearlake Oaks, CA | Registered: May 2001
| IP: Logged |
posted
Yes, I have both mice hooked up at the same time...but, I tried removing the old mouse, plus the old mouse control panels, extensions...restarted and still no go.
I installed the USB card, then the drivers for the USB, then the mouse drivers and control panel, and lastly the new mouse.
I hate to spend much time on something like a new mouse, but the added accuracy will help alot in what I'm doing, plus it's a trial baloon before I put some bigger bucks into a CDR drive.
If you don't have it figured out yet, try this in the mean time...
Uninstall the mouse, then drivers, then reboot. Then reboot again. Then install the mouse, then install the drivers when (hopefully) prompted. Then shut down, un-hook the old mouse, and reboot.
-shane
-------------------- Halo Graphics Clearlake Oaks, CA http://www.halographics.com ntshane1@halographics.com Posts: 308 | From: Clearlake Oaks, CA | Registered: May 2001
| IP: Logged |
-------------------- Albert Motta Ministries Albany, NY http://www.eRev.net Pastor@eRev.net Posts: 1 | From: New York | Registered: Nov 2002
| IP: Logged |
posted
don you dont have computer ..you got a mac....if it was a pc...i would have you fixed in a minute......
-------------------- joe pribish-A SIGN MINT 2811 longleaf Dr. pensacola, fl 32526 850-637-1519 BEWARE THE TRUTH.....YOU MAY NOT LIKE WHAT YOU FIND Posts: 11582 | From: pensacola, fl. usa | Registered: Nov 1998
| IP: Logged |
posted
Bob...yes, I have Mac OS 9.2 installed on this machine. Upgraded to that primarily for the USB and Firewire capabilities. Gotta get a CD burner runnin on this thing in the next couple weeks.
What was the Reverend's flyby all about?
I know, Old Paint...if I didn't have a Mac, you'd have me up and running with the USB in minutes. (I'll e-mail you the rest of this paragraph, Joe. lol)
posted
bob, the thing that's confusing me is I'm not convinced it's a usb problem. The USB is showing up in my system profiler, as is the new mouse. Plus, once I got the drivers for the usb to load right, the light on the mouse comes on at startup. So, there's communication goin on there.
If you take a look at the system profiler image that I uploaded here, it has the usb info in the pci section near the bottom, but the mouse info is at the top, separate. I would think that the mouse would show up to the right of the usb info, like the monitor shows up to the right of the display card info.
Using what logic I have available after just one cup of coffee, seems that the mouse is disjoined from the usb card that it's plugged into.
No, haven't called tech support yet...the thought of press 1 if you have windows, press 2 if you have mac, press 3 if you're ****ed off and ready to take our mouse back to try another brand....
posted
Don, have you tried unplugging the USB mouse then simply plug it back in, with the machine still running?
I actually have to do this with my USB mouse on occassion when I boot the laptop. Sometimes the mouse will work, sometimes it won't. If it doesnt, I just unplug it and plug it back in and it's ready to go.
I've found USB to be quirky at best.
That being said, I think it's time to try a different mouse. The USB card is obviously recognizing it and so is Mac OS, so the only reason I can think of why it wouldn't work is simply a faulty mouse - it happens.
I don't think it has anything to do with the other mouse. If there was a conflict, either the old mouse or the USB card wouldn't be working right, and since the USB mouse is lighting up we know the USB card is functional now. Besides that, there shouldn't ever be problems running multiple pointing devices on a computer. I can run my USB mouse, my old PS/2 mouse and my drawing tablet all on this laptop without any problems. Of course two mice and a radiation board makes for a cluttered desk.
-------------------- "If I share all my wisdom I won't have any left for myself."
Mike Pipes stickerpimp.com Lake Havasu, AZ mike@stickerpimp.com Posts: 8746 | From: Lake Havasu, AZ USA | Registered: Jun 2000
| IP: Logged |
posted
the reverand post....was funny....its just like the new mac tv commercials......"hi i had a pc but....now i got a mac..........and it does everything......"
-------------------- joe pribish-A SIGN MINT 2811 longleaf Dr. pensacola, fl 32526 850-637-1519 BEWARE THE TRUTH.....YOU MAY NOT LIKE WHAT YOU FIND Posts: 11582 | From: pensacola, fl. usa | Registered: Nov 1998
| IP: Logged |
posted
Mike, I'm convinced....gonna pick up another mouse. Wondering if you mean replace the mouse with another brand, or that this particular mouse could be the culprit? I like the fell of this logitech...I think besides the obvious benefits of an optical, that the ergonomics of this particular logitech will likely cut way down on fatigue.
But...at this point....any optical mouse willbe better than one that isn't working right. LOL
Terry and Joe, fill me in on the reverend. Is that some takeoff on a TV commercial or what? I apparently missed something. I seriously doubt that I've watched ten hours of TV since June.
[ November 20, 2002, 04:44 PM: Message edited by: Don Coplen ]
Don, I didn't look that close until Terry pointed it out, but the above quote is post # 1 for REV. Albert. I too, think it is a spoof on the new breed of mac commercials where someone introduces themself & explains how the light went on in their head & they realized that switching to Mac's was their destiny. I checked out the Rev's home page & found a link to his friend Shane French's "Halo Graphics" so maybe not such a huge co-incidence after all.
posted
I use a mac as well, and have for a while. But I have not installed a usb port into one that does not have one. I can tell you, though, that on a mac, you can have as many mice or tablets plugged up as you like and all usually work.... extensions or not. Usually the extensions simply give you access to customizing buttons and such... the mouse itself usually works from the get-go. My guess is a) it is a faulty mouse. or b) (which i lean toward)it is some sort of disconnect with the computer seeing that that thing you have plugged into this new thing is a mouse after all and it needs tweaking a bit somehow.
-------------------- --If you don't care where you are, you ain't lost.
Tony Potter Blind Mice and Company 3001 Bever Ave. SE Cedar Rapids, IA 52403 (319) 573-9001 www.blindmiceandcompany.com tonypotter@yahoo.com Posts: 209 | From: Cedar Rapids, IA | Registered: Nov 1999
| IP: Logged |
Man, am I slow. I totally didn't get that until OP's post. I about died when I read Bryan's post (cuz I can barely stomach those commercials) and linked the post to the eRev (a very good friend of mine) in IM last night.
Yeah, I'm the link right above "The #1 Christian Porn Site." Now That's status!
In any event, I really didn't want this to turn into a "See? Macs Shoooooore suck don't they Don?" post. It's a drag to have computer problems no matter what platform you use.
Hope you get it figured out man.
-shane
-------------------- Halo Graphics Clearlake Oaks, CA http://www.halographics.com ntshane1@halographics.com Posts: 308 | From: Clearlake Oaks, CA | Registered: May 2001
| IP: Logged |
Have you tried to rebuild your desktop? Or to zap your PRAM? May be it could help!
Have you other devices plugged in your USB card? If so, may be you need a powered USB hub.
And are you sure that this USB card and the mouse are MacOS 9.2 compatible?
Just some suggestions.
And you could find support and help on some Mac forums. Macpeople are usually very kind
-------------------- Desire Rusovsky SDG Signs rue du Lac 24 1342 Le Pont Switzerland desire@sdgsigns.com http://www.sdgsigns.com Posts: 218 | From: Le Pont / Switzerland | Registered: Mar 2002
| IP: Logged |
posted
I've got a powermac G3, running system 8.6 with a pci usb card. I am currently using three slots in the card, one for my hp printer, one for my brother laser printer, and one for my logitech optical mouse. All three work great, and have since installing the card. The logitech mouse had a few glitches when I first installed it, but after downloading fixes from their site, havent had a problem since. I use it every day. I cant understand why yours is doing what its doing don. Could be the usb cable, or the mouse itself. You might give my buddy Sam Sanfillipio a call in pinson alabama. He is a mac guru. Im at home now,and I dont have his number here. You might get it through the letterhead database. Hes helped me out quite a few times with little things. There is no reason why the dang thing shouldnt be working. Scratching me head on this one....
-------------------- Maker of fine signs and other creative stuff. Located at 109 N. Cumberland ave. Harlan, Ky. 40831 606-837-0242 Posts: 4172 | From: Ages-Brookside, Ky. Up the Holler... | Registered: Jul 1999
| IP: Logged |
posted
Don, glad you're making progress, and I hope you figure it out soon.. This definitly is not the norm when it comes to Mac.
Brian, The "Expensive" myth is just that, a Myth. you can get a brand spanking new G3 iMac with OS X ( which really is stable, and easy to use) for a mere $799.00 USD. If you want a little more performance choose the G4 Flat Panel display iMac for $1100.00 USD. Not everyone needs a 3,000 powerbook. I know this isn't a Mac Vs. PC debate, and I don't want it to be really, but since I switched from PC's this year to Mac, I've spent more time happy, and productive than ever before. In signmaking, the large drawback is the lack of drivers for a good portion of the equipment that most of us already own. Hopefully we'll see that change, so there is more of an even choice for people. I probably wouldn't have changed to Mac, had they not released the new OS X operating system. It's just that much better in my opinion. Aside from the annoying Apple commercials, I've never been happier, and am slowly converting our offices.
-------------------- Jeff Bailey Rapid Tac Inc. Grants Pass, Oregon Posts: 231 | From: Grants Pass, Oregon, USA | Registered: Feb 2001
| IP: Logged |
posted
I have to admit I've been eyeballing Macs too, and it's a toss-up between an apple and a PC running Linux with the slick new user interfaces (which ironically look more like a mac now than windows).
The Macs are also priced right IMO, given that a homebrew PC with similar quality components costs just as much if not MORE than what apple has to offer. Apple *is* having some killer deals on their machines right now.
Drat.. I just got another message from Windows Update regarding yet another set of security patches available for Windows.. time to reboot.
-------------------- "If I share all my wisdom I won't have any left for myself."
Mike Pipes stickerpimp.com Lake Havasu, AZ mike@stickerpimp.com Posts: 8746 | From: Lake Havasu, AZ USA | Registered: Jun 2000
| IP: Logged |
posted
Mike, if you choose to go Mac, and want to save some bucks, the G4 Cube can be found on Ebay for less than 1k. Neet machines, robust, and a very unique starting point for a powerful system. They generally were 450 Mhz machines, though there were a few 500 Mhz machines with superdrives (CD-RW, DVD player Combo). The 500's with the superdrive are the real sought after machines, and can be upgraded to 800 mhz. I'm sure you know that 800 mhz on a mac is nothing like 800 mhz on a PC. Since the OS X is Unix based, (a derivitive of Free BSD Unix from what I'm told) you can easily run linux on that as well. heck, I think there is a way to convert a PC to Linux, then run OS X on that. It's getting wild..
-------------------- Jeff Bailey Rapid Tac Inc. Grants Pass, Oregon Posts: 231 | From: Grants Pass, Oregon, USA | Registered: Feb 2001
| IP: Logged |
![[Smile]](smile.gif)
![[Big Grin]](biggrin.gif)
![[Confused]](confused.gif)
![[Wink]](wink.gif)
Printer-friendly view of this topic