I am wrighting to say hello to everyone and that I am very glad to be able to finally log in and post.(I tried several years ago but couldn't log in for some reason.) My question is about mounting enlarged photos. I recently enlarged some old photos to poster size on my Versa Camm and spray glued them on to Foam Core for a fund raiser for the local historical committee. My problem is that foam core doesn't seem to be the best material due to its light weight and warping,I also had some trouble with bubbles developing on some of the photos.
Posted by Jane Diaz (Member # 595) on :
You might want to try a different backing material. I don't know where you get your sign supplies from but you might see what they have that is light weight, like Sintra or coroplast.
Posted by Barb Schilling (Member # 13) on :
I really like to use Styrene for display mounting. Comes in several thicknesses, can be cut with mat knife, good adhesion of vinyls, super smooth surface.
Posted by Sheila Ferrell (Member # 3741) on :
Philip, I have no idea what to do about the photos, but . . .
Welcome to Letterville anyway. Posted by Rick Beisiegel (Member # 3723) on :
Same here. I cannot solve your problem, but, I just wanted to chime in and say "Welcome"
[ October 25, 2005, 04:31 PM: Message edited by: Rick Beisiegel ]
Posted by Ricky Jackson (Member # 5082) on :
Hi Phil; welcome to Letterville. I like styrene too.
Posted by Ryan Long (Member # 5881) on :
you could also try UltraBoard, it is 2 layers of styrene with a foam core...warp-resistant. check out the ultramount on that site too.
Posted by Bruce Bowers (Member # 892) on :
I have eliminated the warping by laminating cheap vinyl (and do mean the absolute cheapest pool liner patch crap) on the back side of the foamboard. The warping is caused by the draw caused by the pulling action of the print on the board.
I use a Daige Quickmount to apply the prints and the cheapo vinyl. The use of the laminator eliminates the bubble problem with the prints, too.
Editted to say "Welcome to Letterville!"
[ October 25, 2005, 06:03 PM: Message edited by: Bruce Bowers ]
Posted by KARYN BUSH (Member # 1948) on :
oopsi
[ October 25, 2005, 06:09 PM: Message edited by: KARYN BUSH ]
Posted by KARYN BUSH (Member # 1948) on :
welcome!
yep i print on matt calender/laminate then apply to sintra.
Posted by Bob Kaschak (Member # 3146) on :
Welcome,... you are just down the road from me.
Peace out, Bob
Posted by Neil D. Butler (Member # 661) on :
If you are printing on paper stock and spraying glue on the back then I believe you have to use a paper product like foam core, Gater Foam would be more appropiate. I'm finding that you can't mix a paper product with a Plastic product, The Plastic will contact and expand and the paper won't, this will cause wrinkles over a short period of time.
But like someone said print it on a pressure sensitive vinyl and apply directly to sentra, it works perfect and no fooling around.
Posted by Mike Pipes (Member # 1573) on :
Printing on vinyl and applying it to sintra or even an aluminum blank would solve any bubble/pucker and warping issues.
When you print on paper and sprayglue the entire sheet down, that's just the problem you're going to run into.
When you mount photos it's best to mount them behind a matte, then you can use mounting tape along just ONE edge of the photo, or just two opposite corners. This allows the paper to expand and contract as environmental conditions change, without trying to pull against the surface the photo is mounted onto.
Posted by Bill Modzel (Member # 22) on :
I'm a fan of gatorfoam here but I either use adhesive backed paper to begin with. Other wise I have a roll of 3M Df adhesive 24" wide and run it through our antique laminator.
![[Smile]](smile.gif)
![[Cool]](cool.gif)